Mk-diamond MK-100 Uživatelský manuál

05.2013MK-100 TILE SAWOWNER'S MANUALPARTS LIST &OPERATING INSTRUCTIONSwww.mkdiamond.comCaution: Read all safety and operating instructions be

10Use of under sized extension cords result in low voltage to the motor that can result in motor burnout and premature failure. MK Diamond warns that

11MK-100 TILE SAW SAFETY SAFETY LABEL LOCATIONSSafety label

12MK-100 TILE SAW PRODUCT SPECIFICATIONSPRODUCT SPECIFICATIONSThe MK-100 is a versatile Tile Saw.

13MK-100 TILE SAW CONTENTName addressCitystate zip CodephoNe Faxe-

14MK-100 TILE SAW TRANSPORTTRANSPORTThe MK-100 is designed with a rigid

15MK-100 TILE SAW STANDThe MK-100 weighs ninety-six (96) poun

16MK-100 TILE SAW ASSEMBLYFollow the assembly instructions to prepar

17MK-100 TILE SAW ASSEMBLYThe Adjustable Cutting Guide can be used o

18Prior to beginning work, a pre-start inspection of the saw should be performed.(A) Ensure the ON/OFF Switch is in the OFF position.(B) Verify the

19CONNECTING WATER PUMP(A) Connect the Cooling Transfer Tube to the inlet connection of the Blade Guard.(B) Connect the Water Pump power cord to the

2INTRODUCTION Congratulations on your purchase of a MK-100 Tile Saw. We are certain that you will be pleased with your purchase. MK Diamond takes p

20RE-CIRCULATIONWhen using the re-circulation method, the water should be changed often for longer pump life.(A) Ensure the Drain Plug is in-stalled

21 MK-100 OPERATIONPORTABLE GENERATORGROUND FAULT INTERRUPTERIf using a portable gener

22(D) Verify proper cooling ow on both sides of the blade (See Maintenance Section to increase/decrease ow).Cutting Straight Edges MK-100

23 MK-100 OPERATION(D) Perform the cut. Turn the motor OFF when work is complete.45° Mi

24Off-angle CuttingDO NOT FORCE THE TOOL. It will do the job better and safer at the rate for which it was designed.CAUTION(A) Place the 90° Protract

25For small tiles (6" tile or smaller) the Cutting Head should be in the rear pivot hole and the Motor Post should be in the forward post retaini

26 MK-100 CUTTING HEAD ADJUSTMENTAdjusting the Motor Post for Maximum Cutting LengthThe Cutting Head and Motor Post ar

27CLEANUPIf an external water source was used, steps A through C may be skipped. Dispose of waste water in accordance with applicable Federal, State a

28 MK-100 MAINTENANCEMAINTENANCEPerform the following after initial purchase and operation of

29 MK-100 MAINTENANCEMonthly Maintenance Cont.(G) Remove the Blade Guard. Lubricate the Blad

3TABLE OF CONTENTS SAFETYSafety Messages 4 General Safety Precautions 4-6California Proposition 65 Message 6 Hazard Symbols 7Electrical Requireme

30 MK-100 MAINTENANCELike most cutting instruments, a diamond blade performs best when it is

31 MK-100 MAINTENANCEThe MK-100 is designed with power transmission Micro-V Belt. In order to

32 MK-100 MAINTENANCE(J) Push the motor toward the front of the Cutting Head to loosen the V

33 MK-100 MAINTENANCECooling Flow(A) Check cooling ow Adjusting Clamp open.(B) Remove the

34 MK-100 TROUBLESHOOTINGMovable Cutting Table Does Not Move Correctly(A) Check that the Guide Bar i

35NOTES

36 MK-100 EXPLODED VIEW

37 MK-100 PARTS LISTItem Description QtyPart#A ACCESSORY PACK N/AA1 WRENCH, 15/16 CL

38Item Description QtyPart#G BLADE GUARD N/AG1A SCREW, HEX HEAD (NOT SHOWN) 1 162473G1 BLADE GUARD, 110/115 1 162481G2 ELBOW, 1/8 MNPT X 1/4 BARB 90°

39Item Description QtyPart#K-M ASSEMBLY, TABLEK TABLEK1 TABLE, 100 1 157660K1A BEARING, 3/4 ID MULTILUBE 2 152227K2 WASHER, 5/16 SAE FLAT 2 151754K3 W

4Read and follow all safety, operating and maintenance instructions. Failure to read and follow these instructions could result in injury or death to

40MK-100 TILE SAW THEORYTypes of Cutting

41ITEM NUMBER DESCRIPTION 1. MK-200, 10 x 5/8 Arbor 2. MK-215, 10 x 5/8 Arbor 3. MK-315, 10 x 5/8 Arbor 4. Dual 45° F

42ORDERING INFORMATIONYou may order MK Diamond products through your local MK Diamond distributor or, you may order direct from MK Diamond.NOTE: Ther

43NOTES

MK Diamond Products, Inc.1315 Storm ParkwayTorrance, CA 90501Toll-Free: (800) 421-5830Phone: (310) 539-5221Fax: (310) 539-5158www.mkdiamond.comMK-100

5MK-100 TILE SAW SAFETY If using an extension cord make sur

6MK-100 TILE SAW SAFETY NEVER LEAVE A TOOL UNATTENDED TURN

7MK-100 TILE SAW SAFETY SILICA DUST WARNINGGrinding/cutting

8MK-100 TILE SAW SAFETY ELECTRICAL REQUIREMENTS AND GROUNDI

9MK-100 TILE SAW SAFETY Supporting Surface Power Tool